久久香蕉国产线看观看精品yw-久久香蕉国产线看观看亚洲卡-久久香蕉国产线熟妇人妻-久久香蕉影院-久久香蕉综合精品国产-久久香综合精品久久伊人

老化測試設備

咨詢熱線

18566398802
首頁 > 標準大全 > ASTM D4329-05標準詳情
相關測試儀器

ASTM D4329-05

(該標準已經被ASTM D4329-13替代)
  本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用。我們愿意和您交流ASTM D4329-05標準細節信息或ASTM D4329-05測試方法,歡迎致電【18566398802】

ASTM D4329-05標準介紹

塑料熒光紫外線暴露測試的標準測試方法:

本測試方法規定了依照G151和G154測試方法對塑料進行熒光紫外線暴露測試的具體程序和測試條件。

ASTM D4329-05英文版本

This standard is issued under the fixed designation D 4329; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.

1. Scope*

1.1 This practice covers specific procedures and test conditions that are applicable for fluorescent UV exposure of plastics conducted in accordance with Practices G 151 and G 154. This practice also covers the preparation of test specimens, the test conditions best suited for plastics, and the evaluation of test results.

1.2 The values stated in SI units are be regarded as standard. The values given in brackets are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

NOTE 1—This practice is technically similar to ISO 4892-3.

2. Referenced Documents

2.1 ASTM Standards:

D 3980 Practice for Interlaboratory Testing of Paint and Related Materials

D 5870 Practice for Calculating Property Retention Index of Plastics

E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

G 113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials

G 141 Guide for Addressing Variability in Exposure Testing on Nonmetallic Materials

G 147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests

G 151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices That Use Laboratory Light Sources

G 154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

G 169 Guide for Applications of Basic Statistical Methods to Weathering Tests

G 177 Tables for Reference Solar Ultraviolet Spectral Distributions: Hemispherical on 37 Degree Tilted Surface

2.2 ISO Standard:

ISO 4892-3 Plastics—Methods of Exposure to Laboratory

Light Sources—Part 3, Fluorescent UV Lamps

2.3 SAE Standard:

SAE J2020 Accelerated Exposure of Automotive Exterior Materials Using a Fluorescent UV and Condensation Apparatus

3. Terminology

3.1 The definitions in Terminology G 113 are applicable to this practice.

4. Significance and Use

4.1 The ability of a plastic material to resist deterioration of its electrical, mechanical, and optical properties caused by exposure to light, heat, and water can be very significant for many applications. This practice is intended to induce property changes associated with end-use conditions, including the effects of sunlight, moisture, and heat. The exposure used in this practice is not intended to simulate the deterioration caused by localized weather phenomena, such as, atmospheric pollution, biological attack, and saltwater exposure.

 (Warning—Variation in results may be expected when operating conditions are varied within the accepted limits of this practice. Therefore, no reference to the use of this practice should be made unless accompanied by a report prepared in accordance with Section 8 that describes the specific operating conditions used. Refer to Practice G 151 for detailed information on the caveats applicable to use of results obtained in accordance with this practice.)

NOTE 2—Additional information on sources of variability and on strategies for addressing variability in the design, execution, and data analysis of laboratory-accelerated exposure tests is found in Guide G 141.

4.2 Reproducibility of test results between laboratories has been shown to be good when the stability of materials is evaluated in terms of performance ranking compared to other materials or to a control.5,6 Therefore, exposure of a similar material of known performance (a control) at the same time as the test materials is strongly recommended. It is recommended that at least three replicates of each material be exposed to allow for statistical evaluation of results.

UVA340光譜圖

溫馨提醒:本ASTM D4329-05可能存在更新的版本,建議尋找ASTM D4329-05的發行商確認。

符合 ASTM D4329-05 標準的
老化試驗箱

  • 紫外線老化箱圖片 紫外線老化箱紫外線老化箱

    QUV是美國Q-lab公司的注冊商標,也是Q-lab公司紫外加速老化設備的統稱,包含QUV/basic、QUV/se、QUV/spary、QUV/cw四個不同型號的產品。

    QUV 馬上詢價
  • 紫外線老化試驗箱圖片 紫外線老化試驗箱紫外線老化試驗箱

    QUV/spray紫外線老化試驗箱相比QUV/se紫外線老化試驗箱增加水噴淋的功能。

    QUV/spray 馬上詢價
近期文章
主站蜘蛛池模板: 国产福利一区二区三区在线视频 | 911视频免费 | 婷婷六月天激情 | 狠狠色噜噜狠狠狠狠98 | 色综合色狠狠天天综合色hd | 久久资源在线 | 欧美大屁股精品毛片视频 | 欧美一区二区三区在线视频 | 97视频在线观看视频最新 | 四虎影院永久在线观看 | 91一区二区在线观看精品 | 97精品国产自在现线免费 | 中文字幕在线视频不卡 | 欧美高清理论片在线观看 | 亚洲高清二区 | 天天综合久久 | 操操操综合网 | 国产午夜精品一区二区三区嫩草 | 狠狠色噜噜狠狠狠狠色综合久 | 国产欧美日韩一区 | 久草在线这里只有精品 | 欧美成人午夜影院 | 天天干夜夜谢 | 国产一区二区免费在线观看 | 成年人免费在线视频 | 免费观看成人碰视频公开 | 国产精品资源在线 | 性一级视频 | 色婷婷一区 | 午夜福免费福利在线观看 | 四虎在线影视 | 超清波多野结衣精品一区 | 久久一区二区三区免费播放 | 日本一级毛片毛片一级毛片 | 亚洲综合插插 | 亚洲色视频在线播放网站 | 亚洲黄色在线视频 | 综合亚洲欧美 | 日韩久久一区二区三区 | 精品久久久久久蜜臂a∨ | 日日噜噜爽爽狠狠视频 |