久久香蕉国产线看观看精品yw-久久香蕉国产线看观看亚洲卡-久久香蕉国产线熟妇人妻-久久香蕉影院-久久香蕉综合精品国产-久久香综合精品久久伊人

老化測試設備

咨詢熱線

18566398802
首頁 > 標準大全 > ISO 4611-2010標準詳情
相關測試儀器

ISO 4611-2010

(該標準已經被廢止替代)
  本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用。我們愿意和您交流ISO 4611-2010標準細節信息或ISO 4611-2010測試方法,歡迎致電【18566398802】

ISO 4611-2010標準介紹

ISO 4611-2010標準簡介

0.1 Various test methods are available for the exposure of plastics to different aggressive agents acting in a combined and simultaneous fashion, such as natural weathering. Other test methods are available for the purpose of a separate evaluation of the action of individual aggressive agents. Among the latter there are, for example, tests for the resistance to specific chemicals and to radiations of a definite spectral range.

For some applications, it may be desirable to evaluate the behaviour of the materials in a hot damp atmosphere just below the saturation limit of water vapour, as well as in the presence of the liquid phase.

In these conditions not only water absorption or leaching of some ingredients of the composition may be observed but also degradation phenomena due to hydrolysis, exudation of plasticizers, etc.

It may also be desirable sometimes to evaluate the behaviour of materials in the presence of a highly corrosive electrolyte, such as a sodium chloride solution (salt mist), which is the principal aggressive agent present in marine environments and of particular importance in the case of nautical applications. It is well known that sodium chloride has no noticeable action on the polymers that are the basic components of plastics, and that salt solutions, owing to their higher osmotic pressure, are normally absorbed by plastics to a lesser degree than pure water, but it cannot be assumed a priori that they have no action on composite materials, containing fillers, reinforcing components or pigments, for instance.

Furthermore, the evaluation of the effect of salt mist can be very important for finished or semi-finished articles which, while basically consisting of plastic materials, do contain some metallic elements, such as moulded-in inserts, thin laminated foils, surface coatings applied by electro-plating or other procedures, or, lastly, metal cores sheathed with plastics by extrusion or by dipping in pastes or fluidized-bed powders.

0.2 Methods and equipment for obtaining reproducible aggressive environments of the above types are well known and have been described by International Standards relevant to other materials and IEC (International Electrotechnical Commission) standards relevant to electrical and electronic components. The same equipment and procedures described in these standards can also be employed for plastics, with appropriate care and adjustments.

0.3 The present International Standard is intended to provide general guidance only, on the choice of suitable equipment and procedures for obtaining the exposure conditions described above and for the preparation of test specimens. It also only gives general guidance on the properties to be evaluated. Specific details are given in the various ISO and IEC publications.

For the expression of results, the present International Standard follows, as far as possible, the same criteria adopted in the existing test methods for the exposure to chemicals (see ISO 175) and to natural weathering or artificial light (see ISO 4582).

0.4 These tests are intended to yield data about the effects of the described exposures on the materials; however, a direct correlation between the experimental results and the behaviour in service is not to be inferred.

1 Scope

1.1 This International Standard specifies the conditions of exposure of plastics to

— damp heat,

— water spray,

— salt mist,

and the methods for the evaluation of the change in some significant characteristics after given exposure stages.

1.2 This International Standard is, in general, suitable for all plastics in the form of standard test specimens, and finished articles or parts thereof.

1.3 This International Standard considers separately methods for the determination of

— change in mass,

— change in dimensions and appearance,

— change in physical properties.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 62, Plastics — Determination of water absorption

溫馨提醒:本ISO 4611-2010可能存在更新的版本,建議尋找ISO 4611-2010的發行商確認。

符合 ISO 4611-2010 標準的
老化試驗箱

  • 鹽霧試驗箱圖片 鹽霧試驗箱鹽霧試驗箱

    Q-FOG CRH1100是一款的具有相對濕度控制功能和溶液噴淋功能的鹽霧試驗箱.

    Q-FOG CRH1100 馬上詢價
  • 鹽霧試驗箱圖片 鹽霧試驗箱鹽霧試驗箱

    Q-FOG CRH600比起SSP/CCT鹽霧試驗箱增加了一個可調濕度控制功能,這意味著CRH鹽霧試驗箱具備更廣泛的標準適用范圍。

    Q-FOG CRH600 馬上詢價
近期文章
主站蜘蛛池模板: 国产欧美精品一区aⅴ影院 国产欧美精品一区二区 | 视频二区欧美 | 91探花在线视频 | 色综合天天 | 91在线视| 久久国产精品吴梦梦 | 97视频在线观看免费视频 | 国产四虎 | 国产精品久久久久久久久免费hd | 国产成人免费午夜性视频 | 九九爱www高清免费人成 | 在线观看视频91 | 亚洲精品综合网 | 六月婷婷啪啪 | 国产精品一区在线免费观看 | 9999人体做爰大胆 | 人人做人人爽久久久精品 | 日韩欧美无线在码 | 羞羞网站在线播放 | 亚洲久久久久久久 | 在线国产播放 | ass曰本人乱妇ass | 欧美日本黄色 | 四虎在线视频观看 | 日本毛片在线看 | 国四虎影永久 | 97久久曰曰久久久 | 亚洲第一成年人网站 | 欧美经典人人爽人人爽人人片 | 国产黄色自拍 | 天天拍天天操 | 色综合五月天 | 日韩黄色录像 | 国产又黄又a又潮娇喘视频 国产又色又爽又黄又刺激18 | 老司机伊人 | 欧美激情社区 | 牛人盗摄一区二区三区视频 | 国产高清一区二区 | 精品乱码一区二区三区在线 | 手机看片久久 | 伊人在综合 |